Lincoln Burson Soloist 3X GT with Sennheiser HD 6XX and HiFiMAN Arya V2

Lincoln’s Burson Soloist 3X GT with Sennheiser HD 6XX and HiFiMAN Arya V2

Published on

Post Info

Good so far!

The System

Listening with

Sennheiser HD 6XX · Headphones: open-back, dynamic, circumaural
  • Impedance: 300 Ω
  • Sensitivity: 103 dB SPL @ 1 kHz, 1 V (as published) ≈ 97.8 dB/mW (calc.)
  • Frequency response: 10 Hz – 41 kHz
  • Plugs / cables supplied: 3.5 mm stereo jack plug (6.35 mm adapter); 1.8 m cable
  • Other: THD <0.1% (1 kHz, 1 V)

Matching notes: At 300 Ω and 103 dB/V, the HD 6XX is a high-impedance load that needs voltage more than current: about 2.2 V (17 mW, 7.5 mA) for 110 dB SPL (calc.). Burson rates the Soloist 3X GT at 1.3 W (XLR) / 0.65 W (SE) into 300 Ω, which is about 19.7 V / 14.0 V RMS (calc.), roughly 19 dB / 16 dB more than that. The Soloist 3X GT’s 0.5 Ω headphone output impedance is 1/600 of the load. [1] [2] [3] [4]

HiFiMAN Arya V2

Burson

Burson Soloist 3X GT · Headphone amplifier / preamp (Class-A) · discontinued
  • Output power (XLR / SE): 16 Ω 10 W / 5 W · 32 Ω 8 W / 4 W · 100 Ω 3.8 W / 1.9 W · 300 Ω 1.3 W / 0.65 W · 600 Ω 0.64 W / 0.32 W
  • Output impedance: 0.5 Ω (headphone); 25 Ω (pre out)
  • Gain: High / Medium / Low; dB not published
  • Inputs: 2x XLR; 2x RCA; mic bypass
  • Input impedance: 35 kΩ
  • Input sensitivity: line level
  • Outputs: XLR + RCA pre out; RCA subwoofer out; 4-pin XLR + SE headphone
  • Other: Model R-120X (“GT3”); THD <0.0015%; FR ±1 dB 0-48 kHz

[3] [4]

Also in the system

Denafrips Ares II · DAC: discrete R2R ladder DAC (NOS / OS modes) · discontinued
  • Frequency response: 20 Hz – 70 kHz (-3 dB)
  • Output impedance: 625 Ω (RCA); 1.25 kΩ (XLR)
  • Output voltage: RCA 2.2 V · XLR 4.4 V
  • Inputs: USB (PCM to 1536 kHz, DSD1024); 2x coaxial; 2x Toslink (24/192, DSD64 DoP)
  • Outputs: RCA; XLR
  • DAC / chipset: discrete R2R ladder (no DAC chip); FPGA DSP; STM32 USB
  • Other: THD+N 0.004%; S/N 115 dB; dynamic range >119 dB; crosstalk -124 dB; <=20 W; 215 x 230 x 45 mm

Matching notes: Burson lists the Soloist 3X GT’s analogue inputs as line level (35 kΩ input impedance). The Denafrips Ares II is rated at 2.2 V (RCA) / 4.4 V (XLR) output. [5] [6] [3] [4]

Specs from manufacturer data unless a source below says otherwise. “calc.” values are worked out from those figures (V = √(P × R); 110 dB SPL used as a loud reference level). Gear listed without specs is not in our spec library yet.

  1. Sennheiser HD 6XX: support.sennheiser-hearing.com
  2. Sennheiser HD 6XX: us.sennheiser-hearing.com
  3. Burson Soloist 3X GT product page
  4. Burson Soloist 3XGT User Manual V2.0 (Burson downloads)
  5. Denafrips Ares II: iiwireviews.com (review reproducing denafrips spec sheet)
  6. Denafrips Ares II: head-fi.org (review reproducing denafrips spec sheet)